Continuous Phase Research Articles

UiO-66@Fe3O4 nanocomposite as an adsorbent in dispersive solid phase extraction of metformin in surface water and wastewater

Metformin, an anti-hypoglycemic medication, has been used for decades due to its efficiency and is the most consumed pharmaceutical drug worldwide. Consequently, monitoring its concentration in environmental water is important due to its suspected effect on human health and aquatic life. This study reported the extraction, preconcentration, separation and determination of metformin (MET) in waters. Dispersive solid phase extraction (dSPE) using UiO-66@Fe3O4 nanocomposite as a sorbent was used to extract and preconcentrate MET. The high-performance liquid chromatography-diode array detector (HPLC-DAD) achieved the separation and quantification of MET in the samples. Experiemental design was used to optimise influential variables in the extraction and preconcentration of MET. The linearity, limit of detection (LOD) and limit of quantification (LOQ) for MET were 0.5–100 μg L−1 (R2 = 0.9987), 0.16 μg L−1 and 0.53 μg L−1, respectively. The intraday (n = 10 same-day replicates) and interday (n = 5 consecutive days) precisions reported as relative standard deviations (RSD %) were less than 5%. The accuracy of the method expressed as percentage recovery (%R) ranged from 84 to 112%. The method was applied to extract and preconcentrate MET in wastewater and river water samples. The MET was detected in greater concentrations in wastewater than in river water samples. The validation based on specificity, trueness, linearity, precision, and application to the analysis of MET in real samples showed that the combination of dSPE and HPLC-DAD methods is applicable for MET monitoring in surface water and wastewater. Furthermore, the dSPE/HPLC-DAD method was rapid, simple and suitable for estimating the concentrations of MET in South African surface water and wastewater for the first time. Lastly, the environmental risk caused by the occurrence of MET in surface water was investigated in terms of hazard quotient (HQ). The HQ values were less than unity, suggesting a low possibility risk for the aquatic organisms.

Hydrodynamic Performance Study of a Reciprocating Plate Column Dirven by Electro-permanent Magnet Technology

The reciprocating plate column is a kind of column with the plates driven by a geared motor, and it has advantages in regard to efficiency compared to traditional columns in the extraction process, however, it comes with an increase in energy consumption. A new type of reciprocating plate column driven by electro-permanent magnet technology (EPM) is proposed in this paper to obtain a better performance with lower energy consumption. The feasibility and performance of the proposed column is studied by numerical simulation and experiments with a kerosene–water system. The electro-permanent magnet chuck could provide a maximum amplitude of 12 mm in this study. Kerosene was used as the dispersed phase, and deionized water was used as the continuous phase, in a laboratory-scale 35 mm diameter reciprocating plate column driven by EPM. Hydrodynamic performance experiments were carried out with different flowrates of both phases and reciprocating frequencies. The experimental results show that the electro-permanent magnet chuck, which serves as the driving device of the reciprocating plate column, plays the role of adding energy and increasing the droplet breakage. In addition, the energy consumption of the reciprocating plate column with traditional geared motor and electro-permanent magnet chuck is calculated respectively. Compared with the traditional geared motor, the energy saving of the electro-permanent magnet chuck is as high as 98.55%.

Lateral Flow Assay Biotesting by Utilizing Plasmonic Nanoparticles Made of Inexpensive Metals─Replacing Colloidal Gold.

Nanoparticles (NPs) can be conjugated with diverse biomolecules and employed in biosensing to detect target analytes in biological samples. This proven concept was primarily used during the COVID-19 pandemic with gold-NP-based lateral flow assays (LFAs). Considering the gold price and its worldwide depletion, here we show that novel plasmonic NPs based on inexpensive metals, titanium nitride (TiN) and copper covered with a gold shell (Cu@Au), perform comparable to or even better than gold nanoparticles. After conjugation, these novel nanoparticles provided high figures of merit for LFA testing, such as high signals and specificity and robust naked-eye signal recognition. Since the main cost of Au NPs in commercial testing kits is the colloidal synthesis, our development with the Cu@Au and the laser-ablation-fabricated TiN NPs is exciting, offering potentially inexpensive plasmonic nanomaterials for various bioapplications. Moreover, our machine learning study showed that biodetection with TiN is more accurate than that with Au.

The influence of in situ microfibrillation on the mechanical properties and warpage of low‐density polyethylene/polystyrene composite prepared by fused filament fabrication

AbstractFused filament fabrication (FFF) has been widely adopted due to its simplicity and cost‐effectiveness. But until now, its application materials are still limited. Polyolefin material is one of the most commonly used plastics. However, low‐density polyethylene (LDPE) is rarely used in FFF due to the inadequate strength of the filaments and the warpage of the printed parts. In this work, polystyrene (PS) is added to LDPE to obtain blend filaments. After that, the filaments are used to validate the possibility of in situ microfibrillation directly in the process. The results show that the addition of PS can significantly improve the bending strength, bending modulus, and hardness without affecting the heat resistance and crystal transition of the composite. Besides, the PS dispersed phase can form microfibers under the influence of the shear field. The formation of microfibers can significantly enhance the mechanical properties of composites. The tensile strength and Young's modulus increase by 140% and 221%, respectively. The warping deformation and surface morphology of printed parts are also improved. This study provides a new idea for utilizing low‐strength polyolefin in 3D printing and achieving performance enhancement.

Spearheading a new era in complex colloid synthesis with TPM and other silanes.

Colloid science has recently grown substantially owing to the innovative use of silane coupling agents (SCAs), especially 3-trimethoxysilylpropyl methacrylate(TPM). SCAs were previously used mainly as modifying agents, but their ability to form droplets and condense onto pre-existing structures has enabled their use as a versatile and powerful tool to create novel anisotropic colloids with increasing complexity. In this Review, we highlight the advances in complex colloid synthesis facilitated by the use of TPM and show how this has driven remarkable new applications. The focus is on TPM as the current state-of-the-art in colloid science, but we also discuss other silanes and their potential to make an impact. We outline the remarkable properties of TPM colloids and their synthesis strategies, and discuss areas of soft matter science that have benefited from TPM and other SCAs.

Colloidal synthesis of ZnTe nanocrystals by laser ablation and fabrication of hybrid light emitting device

Zinc telluride (ZnTe) nanocrystals (NCs) have generated the interest of researchers as an electrode material in hybrid light emitting devices (HLEDs) due to its potentially high capacity. However, due to the restricted fundamental charging capacity of the electrode materials, the available energy of existing nanomaterial light emitting devices remains enough for a wide range of applications. In this research, ZnTe nanocrystals were synthesized using Nd: YAG laser at energy 600 mJ by 150 pulse number to form a battery device out of ITO/ZnTe/TPD/Ni. The spectra of the ZnTe NCs were assessed using ultraviolet-visible (UV-VIS) and photoluminescence (PL). The results proved that the synthesized NCs were nanocrystalline structures. The energy gap (Eg) within ZnTe NCs regarded as (PL) spectrum has been identified to be about 3.6 eV. ZnTe NCs produced via laser ablation enhance the functionality of the HLEDs by increasing the carrier's charge mobility and, as a further benefit, by facilitating recombination processes inside ZnTe NCs with TPD organic polymer. In addition to lighting at 3V, current-voltage (I-V) specifications establish suitable environment as well as formation.

Multivariate Bayesian Optimization of CoO Nanoparticles for CO2 Hydrogenation Catalysis.

The hydrogenation of CO2 holds promise for transforming the production of renewable fuels and chemicals. However, the challenge lies in developing robust and selective catalysts for this process. Transition metal oxide catalysts, particularly cobalt oxide, have shown potential for CO2 hydrogenation, with performance heavily reliant on crystal phase and morphology. Achieving precise control over these catalyst attributes through colloidal nanoparticle synthesis could pave the way for catalyst and process advancement. Yet, navigating the complexities of colloidal nanoparticle syntheses, governed by numerous input variables, poses a significant challenge in systematically controlling resultant catalyst features. We present a multivariate Bayesian optimization, coupled with a data-driven classifier, to map the synthetic design space for colloidal CoO nanoparticles and simultaneously optimize them for multiple catalytically relevant features within a target crystalline phase. The optimized experimental conditions yielded small, phase-pure rock salt CoO nanoparticles of uniform size and shape. These optimized nanoparticles were then supported on SiO2 and assessed for thermocatalytic CO2 hydrogenation against larger, polydisperse CoO nanoparticles on SiO2 and a conventionally prepared catalyst. The optimized CoO/SiO2 catalyst consistently exhibited higher activity and CH4 selectivity (ca. 98%) across various pretreatment reduction temperatures as compared to the other catalysts. This remarkable performance was attributed to particle stability and consistent H* surface coverage, even after undergoing the highest temperature reduction, achieving a more stable catalytic species that resists sintering and carbon occlusion.

Existence of density inhomogeneity of liquid Te associated with liquid-liquid phase transition.

We performed small-angle X-ray scattering measurements of liquid Te using a synchrotron radiation facility and observed maximum scattering intensity near 620 K in the supercooled region (melting temperature 723 K). This indicates that density inhomogeneity exists in liquid Te, and the fact that this temperature coincides with the temperature at which the specific heat, sound velocity, and thermal expansion coefficient reach their maxima means that this density inhomogeneity is the cause of these thermodynamic anomalies. The thermodynamic anomalies in liquid Te had already been shown in the 1980s to be comprehensively explained by the inhomogeneity associated with the continuous liquid-liquid phase transition (LLT), but direct experimental evidence for the existence of the inhomogeneity had not been obtained. The present results, together with those already obtained for mixture systems (Te-Se, Te-Ge), indicate the existence of inhomogeneity associated with LLT in liquid Te systems, and strongly support the model. Recently, similarmaximum scattering intensity has also been observed in supercooled liquid water, which exhibits thermodynamic anomalies similar to those of Te, indicating the universality of the inhomogeneous model or LLT scenario to explain the thermodynamics of such "anomalous liquids". Further development of the LLT scenario is expected in near future.&#xD.

Multi-phase shear thickening fluid based on ionic liquid dispersion medium for impact resistance and wear protection

Shear thickening fluids (STFs) have attracted increasing attention as smart materials with unique rheological properties. However, the preparation of STFs usually relies on a composite system of spherical nanoparticles with polyethylene glycol. In this work, novel multi-phase STFs (ILSTFs) were prepared in an ionic liquid by incorporating nanosized SiO2 and rod-shaped calcium metasilicate (CaSiO3) particles as a dispersed phase. Compared to traditional STFs, ILSTFs demonstrate excellent thermal stability. Rheological tests indicate that ILSTFs exhibit continuous shear thickening behavior, resulting in excellent energy absorption and impact wear resistance. In addition, ILSTFs can serve as a new type of lubricant. The tribological properties and impact resistance of ILSTFs were highly correlated with the shear thickening effect, with the multi-phase ILSTF system with CaSiO3 demonstrating superior impact wear resistance compared to the single-phase system. In this study, finite element analysis (FEA) is further utilized to investigate the local damage evolution and energy absorption rate of STF under impact loading, providing insights into the underlying mechanism. This ionic liquid-based STF holds promise for applications as a flexible filling component in the fields of lubrication technology and impact protection structures.

Influence of the alcohol and water grades on surfactant-free colloidal syntheses of gold nanoparticles in alkaline water-alcohol mixtures

AbstractTo make the most of the unique properties of nanomaterials, and to bridge the gap between fundamental and applied research, controlled, green, cheap and energy efficient syntheses of nanoparticles are required. In this respect, room and low temperature surfactant-free colloidal syntheses of nanoparticles obtained in low viscosity and low boiling point solvents, without additives or nature-derived extracts, are promising to develop more active (electro)catalysts. Recently, a room temperature synthesis of surfactant-free gold nanoparticles has been documented (Chem. Mater. 2023, 35, 5, 2173) that requires only water, a base such as NaOH, an alcohol and HAuCl4. Unfortunately, the syntheses of nanomaterials are often sensitive to multiple parameters and it is well acknowledged that reproducibility is a general challenge in the chemical sciences, where the synthesis of nanomaterials is no exception. Here, we investigate the effect of the water conductivity and solvent grade on the surfactant-free low temperature (ca. 30 °C) synthesis of colloidal gold nanoparticles obtained in alkaline mixtures of ethanol and water. The synthesis can be performed with relatively low-grade ethanol but requires high purity water. The importance of water with low conductivity is also stressed for syntheses where ethylene glycol and glycerol are used as source of reducing agents. The results of this study over 100 samples pave the way to greener, more controlled and scalable syntheses of surfactant-free gold nanomaterials.

Independent Phase Control in Gap‐Tuned Metasurfaces for Dual‐Function Switching

AbstractSeeking new ways to actively control the phase using metasurfaces has gained significant attention in recent years, which is the key to achieve controllable wavefronts under external stimuli. Among various active phase control mechanisms, a mechanical method based on gap tuning, termed as gap‐tuned metasurface here, has shown promise in continuous phase adjustment. However, previous studies face limitations in independent and complete phase control at different gap distances, which is crucial in dual‐function switching applications. In this study, a novel type of gap‐tuned metasurfaces are proposed, which can overcome the above limitations through simultaneously manipulating the Pancharatnam–Berry phase and gap‐induced dynamic phase under circularly polarized incidences. Two exemplary gap‐tuned metasurfaces capable of orbital angular momentum (OAM) switching and focusing‐polarity switching are experimentally demonstrated. Furthermore, the special dynamic phase design also exhibits phase conjugate property similar to the Pancharatnam–Berry phase, making circular polarization handedness an alternative route for dual‐function switching. This method provides a straightforward and effective means for the development of active wavefront control devices.

Preparation and investigation of green and cheap deep eutectic solvents for determination of essential and toxic metal ions at trace levels in different coffee products

In this research, a vortex-assisted hydrophobic deep eutectic solvent-based dispersive liquid phase microextraction (VA-HDES-DLPME) method was developed to extract some essential (Fe, Mn and Zn) and toxic (Cd and Pb) metal ions from coffee products. After the VA-HDES-DLPME method, the amounts of the metal ions in the HDES-phase were determined by flame atomic absorption spectrophotometry (FAAS). For selective extraction of metal ions, five HDESs (as extraction solvent) were prepared and tested according to the ultrasonic-assisted procedure. Some dispersive solvents were investigated to ensure the dispersion of HDES in the sample solution. In the VA-HDES-DLPME method, heating and centrifugation steps were not required to separate the HDES-phase from the sample solution. Key factors were investigated and optimized to achieve selective and rapid extraction of metal ions. Under optimized conditions, the working range of the VA-HDES-DLPME method for metal ions ranged from 0.03 to 280 μg kg−1. The detection limits of Fe(II), Mn(II), Zn(II), Cd(II), and Pb(II) ions were 0.01, 0.27, 0.02, 0.015, and 0.18 μg kg−1, respectively. Relative standard deviation and extraction recovery for five replicate runs of 5 μg kg−1 of metal ions were in the range of 1.3%–1.9% and 94 ± 4%-98 ± 2%, respectively. Validation of the VA-HDES-DLPME method was tested by studies on three reference materials. In the final step, the VA-HDES-DLPME method was successfully applied to microwave digestion of coffee samples using a standard addition method. The obtained quantitative recoveries showed the good accuracy of the method.

Electrospun Polylactide—Poly(ε-Caprolactone) Fibers: Structure Characterization and Segmental Dynamic Response

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with the various content from the polymer ratio from 0/100 to 100/0 have been explored. Combining thermal (DSC) and spectropy (ESR) techniques, the effect of biopolymer content on the characteristics of the crystal structure of PLA and PCL and the rotative diffusion of the stable TEMPO radical in the intercrystallite areas of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segment mobility, sorption of the Tempo probe, as well as its activation energy of rotation in the intercrystalline areas of PLA/PCL fibers, were evaluated. The characteristic region of biopolymers’ composition from 50/50 to 30/70% PLA/PCL blend ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible, firstly, to carry out a detailed study of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Dopant induced hollow Ni2P nanocrystals regulate dehydrogenation kinetics for highly efficient solar-driven hydrazine assisted H2 production

Replacing kinetically sluggish oxygen evolution reaction (OER) with a thermodynamically favorable hydrazine oxidation reaction (HzOR) to produce hydrogen has emerged as a more energy-efficient alternative than water splitting. However, the lack of promising bifunctional electrocatalysts hinders its scalable applications. Here, we report a colloidal synthesis of Mn-dopant induced hollow Ni2P nanocrystals (NCs) using a heat-up approach, which act as superior bifunctional electrocatalysts for both HzOR (55 mV at 10 mA/cm2) and hydrogen evolution reaction (HER, 192 mV at 50 mA/cm2). The two-electrode electrolyzer requires a low cell voltage of 59 mV to achieve 10 mA/cm2 and a current density of ∼ 50.4 mA/cm2 to reach 0.5 V. Theoretical studies unraveled that Mn-doping regulates the electronic structure of Ni2P and optimizes the H* adsorption/desorption and dehydrogenation kinetics. When integrated with a Si photovoltaic device, the bifunctional hollow Mn-doped Ni2P NCs enabled solar-driven hydrazine assisted H2 production with a ∼ 14.6 % efficiency.

A new highly accurate and efficient pure visco‐acoustic wave equation for tilted transversely isotropic attenuating media

AbstractThe propagation of seismic waves in attenuating anisotropic media exhibits amplitude dissipation and phase dispersion. To describe its effects, the fractional Laplacian pure visco‐acoustic wave equations capable of producing stable and noise‐free wavefields have been derived. However, except for acoustic approximation, previous wave equations utilize the approximations with lower accuracy in simplifying the denominator of the approximate complex‐valued dispersion relation, resulting in reduced accuracy. To address this concern, we use a combination of complex stiffness coefficients to replace the denominator term of the approximate complex‐valued dispersion relation. This approximation effectively reduces the loss of accuracy caused by ignoring the influence of the velocity anisotropy parameter ε and the attenuation anisotropy parameter εQ in the denominator term, leading to a wave equation with high accuracy in media with large anisotropic parameters ε and δ. In addition, the new wave equation only contains two high‐order spatial partial derivatives and has high computational efficiency. Theoretical analysis and numerical examples demonstrate that the proposed pure visco‐acoustic tilted transversely isotropic wave equation outperforms the previous pure visco‐acoustic wave equation in terms of simulation accuracy. The newly developed wave equation is well suited for the application of Q‐compensated reverse time migration and full waveform inversion in attenuating anisotropic media.

Coercivity enhancement and microstructure optimization of Nd-Fe-Co-B magnets by Dy70Al10Cu20 grain boundary diffusion

The effect of grain boundary diffusion on the magnetic properties and microstructure of Nd-Fe-Co-B sintered magnets is investigated using Dy70Al10Cu20 alloy as the diffusion source. After the secondary annealing of the Nd-Fe-Co-B sintered magnet (Hcj = 7.94 kOe), its coercivity is substantially increased to 13.10 kOe. Following post-diffusion annealing, the coercivity of the sintered magnet significantly increased to 20.86 kOe. Microstructure analysis revealed that after the second annealing, the main phase grains in the magnet were connected but lacked thin intergranular phases. The distribution of Co was uneven, with an abundance of soft magnetic phases rich in Co, which was not conducive to improving coercivity. After diffusion, Dy formed a shell structure with high magnetic crystal anisotropy on the outer side of the main phase grains, leading to a significant increase in coercivity. Al and Cu entered the interior of the magnet, reducing the melting point of the grain boundary phase and promoting the uniform distribution of Co through the flow of the liquid phase. A large amount of thin continuous intergranular phase is generated inside the magnet, which helps reduce the exchange coupling between hard magnetic grains. The experimental results indicate that the Dy-Al-Cu alloy can effectively enhance the grain boundary structure of Nd-Fe-Co-B magnets, reduce the abundance of Co-rich phases, and improve the coercivity of the magnet.

A Numerical Study on Dust Control: Evaluating the Impact of Spray Angle and Airflow Speed in the Coalescence of Droplets and Dust

Spray dust reduction is one of the most economical and effective technologies for controlling coal dust in coal mining faces. We aimed to reproduce a spray dust reduction process in a simulation and investigate the mechanism by which the spray angle and airflow speed influence the dust reduction effect. Based on the DPM (discrete phase model) and the mixture model, we constructed a spray dust reduction evaluation model by considering two-way momentum coupling between the discrete phase and the continuous phase. The results showed that installing nozzles near the dust source (coal mining drum) significantly reduced the dust concentration at the coal mining face from 0.0005 kg/m3 to 0.0001 kg/m3. The increase in airflow speed and spray angle enhanced the horizontal transportation of droplets and dust, providing opportunities for the droplets to condense the dust; however, if the droplets have too large an angle, this will result in an insufficient concentration of droplets in the vicinity of the dust source. When the spray angle is 45°, increasing the airflow speed provides a better dust reduction effect. The nozzle position should also be set scientifically according to the airflow speed. Based on simulation results, a mathematical calculation model of spray dust reduction efficiency was constructed. These results can guide the key parameters of spray dust reduction systems, such as the installation position of the nozzle, the spray angle, and the airflow speed. This paper provides ideas for simulating spray dust reduction for other dust types.

Ecological risk assessment of organochlorine pesticide residues in sediment samples from Lake Tana and Hayqe in Northwest Ethiopia

In most developing countries, including Ethiopia, the excessive use of toxic and persistent pesticides for agricultural and malaria control purposes poses a significant challenge. This study focuses on evaluating the concentration and ecological risks associated with organochlorine pesticides (OCPs) in the sediments of Lake Tana and Hayqe. Employing a laboratory-based cross-sectional approach, the residues of OCPs in sediment samples were extracted using the Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method, followed by dispersive solid phase extraction cleanup (d-SPE) techniques and analyzed for 18 OCPs by gas chromatography coupled to tandem mass spectrometry (GC-MS). The risk Quotient (RQ) method was adopted for ecological risk assessments by using fish, daphnia, and algae as indicators. The concentration of OCPs ranged from 10.11 to 125.65 μg/kg and 10.96–45.17 μg/kg in Lake Tana and Hayqe, respectively. There was a statistically significant difference in the mean concentration of OCPs across the sampling sites in Lake Tana. Deltamethrin and lindane exhibit comparatively lower concentrations among the OCPs, whereas endrin, DDT, and their metabolites were the predominant pesticides in the study area, exceeding WHO and USEPA residue limits, except for endosulfan. Risk Quotient values ranged from 0.006 to 865.4 in Lake Tana and 0.005 to 729.9 in Lake Hayqe, indicating potential low to high ecological risks for aquatic organisms. High ecological risks are particularly evident in fish, daphnia, and algae species exposed to α and β-Endosulfan, DDT, and their metabolites, while specifically in daphnia, endrin poses high ecological risks. The ANOVA test revealed there were statistically significant differences (p-value <0.05) among sampling sites in Lake Tana and the mean values between Lake Tana and Lake Hayqe, underscoring the importance of addressing pesticide-related ecological concerns in the region.

The contribution of auditory imagery and visual rhythm perception to sensorimotor synchronization with external and imagined rhythm.

Sensorimotor synchronization (SMS) refers to the temporal coordination of an external stimulus with movement. Our previous work revealed that while SMS with visual flashing patterns was less consistent than with auditory or tactile patterns, it was still evident in a sample of nonmusicians. Although previous studies have speculated the potential role of auditory imagery, its contribution to visual SMS performance is not well quantified. Utilizing a synchronization-continuation finger-tapping task with a visual stimulus that included implied motion, we aimed to examine how participants' imagery ability, musicality, and rhythm perception affected SMS performance. We quantified participants' SMS consistency in synchronization (with visual cues) and continuation (without visual cues) phases. Participants also performed a perception task assessing their ability to detect temporal perturbations in the visual rhythm and completed musical ability and imagery questionnaires. Our linear regression model for SMS consistency included the trial phase, self-reported auditory imagery control and musicality, and visual rhythm perception as predictors. Significant effects of trial phase and auditory imagery scores on SMS consistency suggested that participants performed SMS more consistently while the guiding visual stimulus was present and that the higher one's self-reported auditory imagery ability, the better their SMS when continuing with unguided rhythm. One's visual rhythm perception accuracy significantly correlated with SMS consistency during the synchronization phase, and there was no correlation between rhythm perception and auditory imagery control. Overall, our results suggested relatively independent contributions of auditory imagery and visual rhythm perception to SMS with visual rhythm. (PsycInfo Database Record (c) 2024 APA, all rights reserved).

Drag reduction assisted emulsification in a micro-channel

An experimental study of the turbulent dynamics of emulsification in a cross-slot microfluidic device is presented. The continuous phase contains a minute amount of an inelastic polymer (xanthan). The Reynolds numbers are sufficiently large (up to 16000) so the drag reduction phenomenon is observed during the emulsification process. The statistics of droplet sizes in the resulting emulsions are measured ex-situ by means of digital microscopy in a wide range of Reynolds numbers and polymer concentrations in the continuous phase. Integral measurements of the statistics of the pressure drops in the micro-channel allow one to systematically map the drag reduction states. Corresponding to each state, the space–time dynamics of the emulsification process are assessed by means of in-situ high speed imaging of the interface between the two fluids which further allows one to extract the characteristic time and space scales associated to the dynamics of the interface. Various dynamic regimes of the microscopic emulsification process are mapped in terms of the Reynolds number and shear thinning rheology of the continuous phase.